JoyC is a Joystick Module designed for the M5StickC. Supports two-handed operation. The main control chip is STM32F030F4, it uses the I2C communication protocol and the M5StickC host for data transmission. The joystick range is from 0 to 200, includes 12 RGB LEDs, and the bottom of the joystick contains 16340 battery holder.

The 8 Environment Sensors Kit, M5Stack Env Kit, includes the 8 Earth, Angle, Pir, Hub, Light, Rgb, Ir and Env Sensors.

This module integrates a Zhongke Weibeidou AT6558 navigation chip and a MAX2659 amplification chip used to amplify the antenna signal. The AT6558 has high performance, supports many types of satellite navigation system, capable of receiving satellite signals on 56 GNSS signal channels from 6 satellite navigation systems, joint location, navigation, weather and more. The module is able to obtain accurate information of global location, fast and precise positioning for any place.

The module can be widely used in vehicle monitoring, car navigation, on-board navigation, notebook navigation, etc. You can connect it to Port C on the M5core via the Grove cable, which is a standard UART interface.

The RoverC is a programmable omnidirectional mobile robot base compatible with the M5StickC and can be started with the insertion of the M5StickC. The main controller of the base is the microcontroller stm32f030f4. The base comes with N20 worm gear motors, which are directly driven by a four-channel motor driver. These motors are connected to the mechanum wheels, which can move in all directions. In addition, two Grove-compatible I2C ports are provided to facilitate expansion to other modules.

PuppyC is a programmable four-legged robot base compatible with the M5StickC. It contains the STM32F030F4 Microcontroller, four 5G90 micro servos, a battery holder and an independent switch. The PuppyC base needs to be used in conjunction with the M5StickC controller. After programming StickC, it communicates with PuppyC through the I2C protocol to control the steering movement.

BugC is a programmable robot base compatible with the M5StickC. It has four DC motors, two RGB LEDs, battery holder and a switch. The BugC base must be used in conjunction with the M5StickC controller. The base comes with a STM32F030F4 Microcontroller, which controls all motors and LEDs, and is controlled by the I2C protocol by M5StickC, which is on top of the base.

The Plus is an enhanced M5 Module that comes with Lipo battery (500mAh), gear potentiometer, IR transmitter, port PORT B (GPIO port) extended, port C (UART port) of the MS core and a microphone solder block. Equipped with MEGA328, it can be a major upgrade of hardware resources, adding PLUS to your work.

Communication Protocol: IIC (0x62).

This is a wireless communication module, integrated with the M8321 NB-IoT module, which provides TD-LTE / FDD-LTE / WCDMA / TD-SCDMA / GSM / GPRS / EDGE frequency band and LCC + LGA package type. It integrated abundant Internet protocols, standard field interface and functions, supported WindowsXP, Windows7, Windows8, Windows10, Linux and Android USB driver.

In the layout of the LTE-4G module, more hardware resources were added, reserved lanes for speakers, 3 LEDs, USB interface, double antenna allowed.

The MFRC522 operates in the frequency range of 13.56 MHz and uses the principle of modulation and demodulation to interact with the RF proximity card. This unit can perform the function of the card reading and writing device, to identify and record various information on the card, to encode and authorize an RF card.

The M5Stick-C is a Mini M5Stack, powered by ESP32, It is a portable IoT development board, easy to use and open source.

What can this do? This small block is able to realize your idea, illuminate your creativity and help with the prototyping of the IoT in a very short time. This takes away many of the pains of the development process.

Finger is a fingerprint sensor that makes fingerprint verification super simple.

The Uart protocol, compact size and ultra low power consumption make the use of MSStack series products very attractive. It performs fast fingerprint matching with the highest level of security and the ideal convenience of the user. You can program to set the level of comparison of the fingerprint recognition and the different security level. If you've ever thought about protecting your project with biometrics, don't forget to include this MSunit Finger.

This unit communicates with the M5Core by UART protocol connected via PORTC.

The M5Stick-C is an ESP5 powered M5Stack mini. It's a portable, easy-to-use, open source IoT development board.