Unlock your potential and get creative with code, electronics, science and engineering, with the BBC Micro:Bit Starter Pack anything is possible! This Micro:Bit V2 Kit contains everything you need to start using Micro:Bit right away. It consists of a BBC Micro:Bit V2, a USB Cable, a Battery Holder with 2 AAA Batteries. The USB Cable allows you to connect your Micro:Bit to a computer. A Batteries allow you to power your BBC Micro:Bit after disconnecting it from the USB.

Make a small Video Display with this Bicolor 8x8 LED Matrix. At just 1.2" on a side, it's pretty visible, but not enough to not plug into a breadboard! Each grid has two LEDs inside so it can display red, green, yellow, or multiplexed. This Matrix is bright, Beautiful and modern with beautiful diffused square lens for a stunning look. There are 24 pins on the side, 12 on each, with 0.1" spacing so you can easily connect it to a breadboard with a line on each side for wiring above.

The Iot:Bit is a Board from Expansion based on IoT for Micro:Bit. It uses the ESP8266 as a Board of WiFi Expansion and serial port to communicate with the Micro:Bit. It also extended all available IO Ports of Micro:Bit which is led by GVS and can extend various 3V E-Blocks like LED, Photosensitive and Servo by using it. At the same time, the Iot:Bit with a built-in buzzer for external sound and a built-in RTC clock for timing without power supply. Let's create your own IoT by MakeCode!

A Module with GPRS Antenna, operation Wireless and SIM Card.

The Cutebot is a rear-wheel drive smart car powered by high-speed twin engines. There is a lot of equipment on board in the Cutebot, including ultrasonic sensor and distance sensor, two RGB LED headlamps and lamps at the bottom, two line tracking probes, an active buzzer as the horn and so on. ! Let's drive your first smart car!

This board is the combination of 3 extremely interesting products: a ESP32 Module with WiFi and Bluetooth, a oLED Display and a battery charging and charging system Lithium-Ion 18650.

The ESP32-CAM is a WIFI + Bluetooth Development Card based on the ESP32 Chip, with the additional possibility of using a camera. It is ideal for a variety of loT applications.

Joystick: Bit V2 is a Joystick based on Micro: Bit . Contains a 4-Way Joystick and 4 Undefined Buttons. Improves the Game Experience with its Integrated Buzzer and Vibration Engine. Joystick: Bit V2 can also be used as a Remote Control with a Good Look and Comfortable Feel.

The TPBot has the appearance of a toy and works as one, since it can be used very easily to follow lines, avoid obstacles or let it work alone (in entertainment mode). However, once the Micro: Bit is inserted, it becomes a super-complete and fully programmable smart car. It's great for working in a classroom, you can expand it with extra electronic modules and add Lego pieces.

RedBear DUO - Wi-Fi BLE IoT Board

A-Star 32U4 Micro

Arduino Wire with ATmega328

Wixel Programmable USB Wireless Module

A-Star 32U4 Prime LV microSD

The SparkFun ESP8266 WiFi Shield is an Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. There are a variety of designs based around the ESP8266, including tiny, modular boards and more accessible development boards like our very own SparkFun ESP8266 

The Motor Driver Motor:Bit to Micro:Bit is compatible with the Micro:Bit and can activate the 2 Channel DC Motor at the same time. Its biggest feature is that we can perform the Motor Direction Control of a Channel with only one IO Port, which reduces the number of IO Ports used.

When you start the 2-channel motor, it is not possible to connect connectors such as LED matrix, IIC, SPI, etc. In addition, it can drive partial IO ports with GVS format. It is a Good Companion for DIY Smart Cars.

The Wukong Board with Lego Support for Micro:Bit is an Integrated Breakout Board with Multiple Functions based on Micro: Bit, which has a Size Similar to Micro: Bit with Buzzer, Servo and Motor Drivers. The board is designed to adapt perfectly to Lego. It takes 20 minutes to complete the upload.

The Wonder Rugged Car by Elecfreaks! An Intelligent Car designed with Mecanum wheels, allowing smooth 360 degree movement in all directions! Omnidirectional movement, as well as compatibility with Lego's! The Wukong Plate inside the Kit has an Integrated Bell, 8-Way Servo Drive, Duel Motor Drive, 4 Rainbow LEDs, as well as 8 Blue LEDs.

Important: Does not include the Micro:Bit Card! But don't worry, get the Micro:Bit Card here: Bit -> Click Here!

The Ring:Bit Pack contains 200 LEGO compatible parts and the necessary electronics to assemble and program 6 different projects with Micro:Bit and Microsoft MakeCode.

Important: Does not include the Micro:Bit Card! But don't worry, get the Micro:Bit Card here: Bit -> Click Here!

JoyC is a Joystick Module designed for the M5StickC. Supports two-handed operation. The main control chip is STM32F030F4, it uses the I2C communication protocol and the M5StickC host for data transmission. The joystick range is from 0 to 200, includes 12 RGB LEDs, and the bottom of the joystick contains 16340 battery holder.

The 8 Environment Sensors Kit, M5Stack Env Kit, includes the 8 Earth, Angle, Pir, Hub, Light, Rgb, Ir and Env Sensors.

This module integrates a Zhongke Weibeidou AT6558 navigation chip and a MAX2659 amplification chip used to amplify the antenna signal. The AT6558 has high performance, supports many types of satellite navigation system, capable of receiving satellite signals on 56 GNSS signal channels from 6 satellite navigation systems, joint location, navigation, weather and more. The module is able to obtain accurate information of global location, fast and precise positioning for any place.

The module can be widely used in vehicle monitoring, car navigation, on-board navigation, notebook navigation, etc. You can connect it to Port C on the M5core via the Grove cable, which is a standard UART interface.

PuppyC is a programmable four-legged robot base compatible with the M5StickC. It contains the STM32F030F4 Microcontroller, four 5G90 micro servos, a battery holder and an independent switch. The PuppyC base needs to be used in conjunction with the M5StickC controller. After programming StickC, it communicates with PuppyC through the I2C protocol to control the steering movement.

BugC is a programmable robot base compatible with the M5StickC. It has four DC motors, two RGB LEDs, battery holder and a switch. The BugC base must be used in conjunction with the M5StickC controller. The base comes with a STM32F030F4 Microcontroller, which controls all motors and LEDs, and is controlled by the I2C protocol by M5StickC, which is on top of the base.

The Plus is an enhanced M5 Module that comes with Lipo battery (500mAh), gear potentiometer, IR transmitter, port PORT B (GPIO port) extended, port C (UART port) of the MS core and a microphone solder block. Equipped with MEGA328, it can be a major upgrade of hardware resources, adding PLUS to your work.

Communication Protocol: IIC (0x62).

The MFRC522 operates in the frequency range of 13.56 MHz and uses the principle of modulation and demodulation to interact with the RF proximity card. This unit can perform the function of the card reading and writing device, to identify and record various information on the card, to encode and authorize an RF card.