Digital Push Button (Green)

A 100kohms Ntc Thermistor.

A 10kohms Ntc Thermistor.

A 1kohms Ntc Thermistor.

A 33kohms Ntc Thermistor.

This Module is a Rotary Incremental Encoder. It encodes the shaft rotation signal and outputs the signal by electronic pulse. The Grove –Encoder is a module of the Grove series and has a standard Grove interface. When you need to add a knob to your project, for example a volume knob for a speaker, a selection panel or a digital input, this should be your first choice.

The HC-12 433MHz Transceiver is a wireless communication Module, which is based on the RF SI4463 chip, has a built-in microcontroller and can be configured by AT commands, the maximum output power is 100mW (20dBm) and the receiver sensitivity differs from: 117dBm to -100dBm, depending on the transmission speed. Accepts 3.2V - 5.5V and can be used with 3.3V and 5V UART voltage devices.

A Module with GPRS Antenna, operation Wireless and SIM Card.

The Kit Set of Torix Connectors is widely used in building wiring. By selecting the best insulation material, it is durable, corrosion free, anti-aging, pressure 4kv and against electric shock. It breaks the disadvantage of the traditional wiring method which is problematic in wiring, easy to leak, and easy to corrode.

The imported PL2303HX controller can stabilize the flash at high speed. With a 500mA auto-recovery fuse for protection and two data transmission indicators that can monitor the data transfer status in real time. The entire board is coated with a high-quality transparent heat-shrinkable layer, rendering the PCB in a state of isolation from the outside, so that the board is not burned. Electrostatic package, ensures that the plate will not be damaged before use. Supports WIN7 system.

MP3 Player Shield - SparkFun

Analog turbidity sensor for Arduino

SparkFun OpenScale

ITeaduino Tiny Digispark

FemtoBuck LED Driver - SparkFun

LinkIt Smart 7688 Duo - Arduino to Linux

Load Cell - 50Kg

SparkFun OpenLog

XBee 6.3mW Wire Antenna - Series 2C ZigBee Mesh

Flexibility Sensor 2.2

Gravity: IO Expansion Shield for Arduino V7.1

This package includes a Sensor of Level of Water and a Sensor of Humidity from Solo. If the plates have water covering the sensor components, an analog value will be available on the "SIG" connection. The Sensor of Level of Water can detect up to 4cm of water. This way, you can check if your aquarium, or your pet's water bowl, still has enough water. You can use the Sensor of Moisture of the Soil to check your plant's soil or growing environment, for example.

DHT22 is a digital capacitive humidity sensor and humidity module is one that contains the compound has been calibrated with digital signal output from the temperature and humidity sensors . < / p>

Can be used to monitor the heart rate of the patient and athlete. The result can be displayed on a screen via the serial port and can be saved for analysis.

This is the Mini Reed Magnetic Sensor Module for Arduino! Reed switches are driven by magnets and are used in Mechanical Systems as Proximity Sensors.

This is the FeatherWing Adalogger: it adds a real-time clock with battery and micro SD card storage to any Feather mainboard. Using the Headers, you can connect a FeatherWing to the top of your board and let the board fly!

The 8 Environment Sensors Kit, M5Stack Env Kit, includes the 8 Earth, Angle, Pir, Hub, Light, Rgb, Ir and Env Sensors.

Color is a Light to Digital Color Converter with IR Filter. The TCS3472 Device provides a digital red, green, blue (RGB) return and sharp light detection values. An infrared blocking filter, integrated in the chip and located in the color-sensing photodiodes, minimizes the infrared spectral component of the received light and allows color measurements to be made accurately.

This unit communicates with the M5Core through the Grove (I2C) port. The address is 0x29.