This site uses cookies to improve your experience. By navigating this site, you consent to the use of cookies. Learn more about our cookies.

Kit de Par de Codificador Magnético para Motoredutores de Micro-Metal

€8.64

(SEM IVA 7.02€)

Pololu
i0354pl
Quantity
There are not enough products in stock

Magnetic Encoder Pair Kit for Micro Metal Gearmotors

Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit.

Overview:

This kit includes two dual-channel Hall Effect sensor boards and two 6-pole magnetic discs that can be used to add quadrature encoding to two micro metal gearmotors with extended back shafts (motors are not included with this kit). The encoder board senses the rotation of the magnetic disc and provides a resolution of 12 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output shaft, multiply the gear ratio by 12.

0J5824.300.jpg?93a68639bea65d7f435559f94

This compact encoder solution fits within the 12 mm × 10 mm cross section of the motors on three of the four sides, and it only extends 0.6 mm past the edge of the fourth side (note: if you need it to be flush with that last side, you can carefully grind the board down a little and solder to the remaining half-holes). The assembly does not extend past the end of the extended motor shaft, which protrudes 5 mm beyond the plastic end cap on the back of the motor.

Pinout and installation

The encoder board is designed to be soldered directly to the back of the motor, with the back shaft of the motor protruding through the hole in the middle of the circuit board. One way to achieve good alignment between the board and the motor is to tack down the board to one motor pin and to solder the other pin only when the board is flat and well aligned. Be careful to avoid prolonged heating of the motor pins, which could deform the plastic end cap of the motor or the motor brushes. Once the board is soldered down to the two terminals, the motor leads are connected to the M1 and M2 pads along the edge of the board; the remaining four pads are used to power the sensors and access the two quadrature outputs:

0J6835.250.jpg?189bee4dc485a11ae8496616d0J6834.330.jpg?6cbae50be958eb2776625398d

The sensors are powered through the VCC and GND pins. VCC can be 2.7 V to 18 V, and the quadrature outputs A and B are digital signals that are either driven low (0 V) by the sensors or pulled to VCC through 10 k? pull-up resistors, depending on the applied magnetic field. The sensors’ comparators have built-in hysteresis, which prevents spurious signals in cases where the motor stops near a transition point.

0J5831.600.jpg?b37c879d2899289012b77d928

Encoder A and B outputs of a magnetic encoder on a high-power (HP) micro metal gearmotor running at 6 V.

The board’s six pads have a 2 mm pitch, so they do not work with common 0.1? connectors. One option for connecting to the board is to solder in individual wires, such as in the example below:

0J5832.350.jpg?1a7afd1aeb0cd22d610efcf66

Alternatively, you can solder a 2mm-pitch connector to the board. The examples below show a male header, which gives you the option of making a detachable cable terminated by a 6-pin 2mm-pitch female header. If the pins are angled over the motor, as shown in the picture below, they will just barely protrude through the holes in the board. Note that in this orientation, there is room to plug in a female header even when our extended micro metal gearmotor bracket is being used.

0J5833.350.jpg?41e195acb26a7f1603c41e679

If the pins are pointed away from the motor, they will need to be angled so that they sufficiently clear the magnetic disc. With a decent soldering iron, it is possible to solder them in this orientation even after the encoder has been installed on the motor.

0J5834.600.jpg?209aacd4401a461a9d2c8af95

Once the board is soldered to the motor, the magnetic encoder disc can be pushed onto the motor shaft. One easy way to accomplish this is to press the motor onto the disc while it is sitting on a flat surface, pushing until the shaft makes contact with that surface. The size of the gap between the encoder disc and the sensor board does not have a big impact on performance as long as the motor shaft is at least all the way through the disc.


Schematic diagram

0J5830.600.jpg?35ff94e36e9e7ded5f84f1f58

Includes:

• 1x Magnetic Encoder Pair Kit for Micro Metal Gearmotors.

No customer reviews for the moment.

Related Products

DC Motor Encoder 12v 251Rpm 18kg/cm - DFRobot

0 Review(s) 
There are not enough products in stock
Price €34.28

This is a gear motor with encoder , model No. GB37Y3530-12V-251R. It is a powerful 12V engine with a 43.8: 1 metal gearbox and an integrated quadrature encoder that provides a resolution of < strong> 16 counts per rotation of the engine shaft, which corresponds to 700 counts per rotation of the gearbox output shaft.

New Order