The HC-12 433MHz Transceiver is a wireless communication Module, which is based on the RF SI4463 chip, has a built-in microcontroller and can be configured by AT commands, the maximum output power is 100mW (20dBm) and the receiver sensitivity differs from: 117dBm to -100dBm, depending on the transmission speed. Accepts 3.2V - 5.5V and can be used with 3.3V and 5V UART voltage devices.

A Module with GPRS Antenna, operation Wireless and SIM Card.

The imported PL2303HX controller can stabilize the flash at high speed. With a 500mA auto-recovery fuse for protection and two data transmission indicators that can monitor the data transfer status in real time. The entire board is coated with a high-quality transparent heat-shrinkable layer, rendering the PCB in a state of isolation from the outside, so that the board is not burned. Electrostatic package, ensures that the plate will not be damaged before use. Supports WIN7 system.

This ESP8285 ESP M2 Module provides easy-to-use WiFi for any UART port and is compatible with the HC-06 Bluetooth modules. If your project uses Bluetooth, it is very easy to convert it to WiFi. Using the integrated web interface, WIFI-UART communication can be configured for TCP or UDP sockets on any port.

NodeMcu consists of open source firmware and a development kit that helps to prototype your IoT (Intemet of Things) project through some lines of Lua language. The NodeMcu has integrated ESP-12 serial WiFi with GPIO, PWM, ADC, I2C and 1-WIRE capabilities, integrates USB-TTL serial with super reliable industrial strength CH340 for superior stability on all supported platforms.

Remote Control Compatible Garage 4 Channels Rolling Code (Water Resistant)

Replace all your Command Confusion with the Broadlink RM Mini 3 Universal Smart Home Wifi IR Remote Control with App and Professional Support, Compatible with Scene and Suspend Mode, Exceptional Hardware Configuration and Time function.

RF Link Transmissor - 434MHz

2.4GHz SMA - 3dBi antenna

Programador AVRISP STK500 AVR USB Atmega Attiny

LinkIt Smart 7688 Duo - Arduino to Linux

3dBi GPS antenna SMA connector

XBee 6.3mW Wire Antenna - Series 2C ZigBee Mesh

4 Bits Digital LED Display

Módulo 433MHZ LORA com alcance 3000m.

O SM5100B é um módulo GSM miniatura, quad-band 850 / EGSM 900 / DCS 1800 / PCS 1900, que pode ser integrado num grande número de projetos sem fios. Você pode usar este módulo para realizar quase qualquer coisa que um telemóvel normal pode - mensagens de texto SMS, GSM / GPRS, o TCP / IP, e muito mais!

Converter SSOP28 to DIP28.

2.4 GHz 3dBi foldable antenna with reverse bias - SMA RF connector. Perfect for prototyping with RF ICs and Xbee modules. 50 ohm impedance. 10.16cm in length.

The RFID Smart Lock can provide good security protection for your personal items, in addition to protecting your privacy. It can also improve the safety of children at home, prevent them from being free to open drawers or cabinet doors.

Each Card pre-programmed with a unique identification number, printed on the card. The Identification Card is suitable for the 125KHZ Card Reader and the Reading Distance is 0cm to 10cm. Used in Identification, Financial Identification, Access Control Systems, Low Frequency Identification Cards and so on. Read-only, not HID card.

It is an easy to use Sensor ID 125Khz Card Reader. Quick to read RFID tags. Plug and play, no extra driver needed. Used in many RFID application systems, such as personnel identification, logistics, access control, conference system, anti-counterfeiting system and industrial production process control.

Cable USB to Serial Adapter RS232, 1,5m Length.

The Arduino WTV020-SD MP3 Module is a voice recording module with 1GB SD Card storage capacity. You can upload WAV and AD4 format files that conform to FAT formatting. It supports 6KHz to 32KHz, being 36KHz for AD4 files and 6-16KHz for voice sampling rate (Audio Sampling).

USB2.0 Standard, Backward Compatible, According to RS485 Standard.

Multimeter with 50-500V AC 0-100A to measure the current voltage.

Multimeter with 50-500V AC 0-100A to measure the current voltage.

Multimeter with 50-500V AC 0-100A to measure the current voltage.