Carbon monoxide detector with alarm - orno

The HC-12 433MHz Transceiver is a wireless communication Module, which is based on the RF SI4463 chip, has a built-in microcontroller and can be configured by AT commands, the maximum output power is 100mW (20dBm) and the receiver sensitivity differs from: 117dBm to -100dBm, depending on the transmission speed. Accepts 3.2V - 5.5V and can be used with 3.3V and 5V UART voltage devices.

A Module with GPRS Antenna, operation Wireless and SIM Card.

TOSR02-T - USB / Wireless 5V 2-channel Relay Module Support for temperature sensor

The Kit Set of Torix Connectors is widely used in building wiring. By selecting the best insulation material, it is durable, corrosion free, anti-aging, pressure 4kv and against electric shock. It breaks the disadvantage of the traditional wiring method which is problematic in wiring, easy to leak, and easy to corrode.

Solid State Relay - 8 Channels

15A Individual DC Motor Controller

LCD Gráfico 128x64 STN LED Backlight

SparkFun OpenScale

SparkFun humidity sensor - HIH-4030

LinkIt Smart 7688 Duo - Arduino to Linux

SparkFun OpenLog

Gravity: IO Expansion Shield for Arduino V7.1

The Pololu USB to serial adapter is great for connecting microcontroller designs to a personal computer. The adapter uses 3.3 V signal levels so you can connect it directly to any microcontroller running at up to 5 V without the hassle of an RS-232 to TTL level converter.

DFRobot Relay Shield  V2.1 is a completely new design which is capable of controlling 4 relays at a time.

The W5500 Ethernet Shield v1.0 can be used to provide your projects with internet connectivity.W5500 enables users to have the Internet connectivity in their applications just by using the single chip in which TCP/IP stack, 10/100 Ethernet MAC and PHY embedded. The shield also have two Grove connectors and a microSD card socket to support projects which require storing large amounts of data from Grove sensor. The RJ45 port (Where the Ethernet cable is connected to) is low enough to allow you to stack more shields on top of this one if needed.

This version of the Ethernet Shield is not only compatible with Mega 1280 and 2560, but also provides a Micro SD card slot for read / write

This relay shield is capable of controlling 4 relays . The maximum switching power can be 360VA / 90W . It can be controlled directly by the Arduino by means of digital IOs digital with external power of 9v . With integrated xbee socket and APC220 socket, it can be controlled wirelessly via Xbee / bluetooth / APC220 . Make it an ideal solution for home automation and robotics.

Play your .mp3 files stored by USB or SD card. For Use (12V): Place a 68Ohm/1W Resistor in series with the (+) of the Power Supply, to avoid excessive dissipation.

This LED Matrix 24 × 8 display is specially designed for the FireBeetle series. It supports low power mode and scroll display. With HT1632C high-performance LED driver chip , each led has an independent register, which facilitates separate driving. Integrates a 256KHz RC clock, only 5uA in low power mode, supports 16-scale PWM brightness adjustment. This product also works with another Arduino microcontroller like Arduino UNO (same as DFRduino UNO).

Can be used to monitor the heart rate of the patient and athlete. The result can be displayed on a screen via the serial port and can be saved for analysis.

Now, it's time to add a more sophisticated interactive way to your project. The DFRobot touch kit comes with three types of touch sensors . A ipod styple touch wheel, a touch touch screen that supports backlit and a grid touch pad that can recognize something unique.

The 8 Environment Sensors Kit, M5Stack Env Kit, includes the 8 Earth, Angle, Pir, Hub, Light, Rgb, Ir and Env Sensors.

Finger is a fingerprint sensor that makes fingerprint verification super simple.

The Uart protocol, compact size and ultra low power consumption make the use of MSStack series products very attractive. It performs fast fingerprint matching with the highest level of security and the ideal convenience of the user. You can program to set the level of comparison of the fingerprint recognition and the different security level. If you've ever thought about protecting your project with biometrics, don't forget to include this MSunit Finger.

This unit communicates with the M5Core by UART protocol connected via PORTC.

When you assign a high level to the module pin, the electro magnet can suck magnetically conductive objects. Otherwise, it will release the object.

An electro magnet is a type of magnet in which the magnetic field is produced by electric current. An electric current flowing in a wire creates a magnetic field around the wire, due to the Ampere Law. To focus the magnetic field on an electro magnet, the wire is wound into a coil with many twists of wire side by side. The Magnetic Field of All Twists of the Wire passes through the Coil Center, creating a Strong Magnetic Field there.

It's Easy to Use to Learn the Electro Magnet Principle.

This UV Sensor is capable of detecting UV solar radiation using a simple UVM-30A chip. It can be easily configured for projects with Arduino to monitor UV Index, analyze UV-A lamps or DIY projects as plant growth analysis.

This Shuck Socket it is easy to use and to install.